|Topic Review (Newest First)|
|05-27-2019 03:27 PM|
Originally Posted by karol View Post
1) Select Honda User at the login screen
2) Select bike size 751 and bigger
3) Then select CRF1000
4) the select what you want from all the OEM accessories with all the installation documentations.
|05-26-2019 04:31 PM|
Originally Posted by jalize View Post
Would you mind to send me the link to the Honda documentation please? I tried to search on the Honda Germany web page, but without any success.
|03-30-2019 04:23 PM|
can you ping me a reply with contacts re wiring / looms
The 2018 models have the 12v Accessory socket plugged into the main loom, completely separate from the front option connector.
can you ping me a reply with contacts
have a need for a switched relay loom to be installed to power 2 x 18w spots
|03-24-2019 01:27 PM|
Originally Posted by deltabi View Post
I have used the Eastern Beaver 3CS, really easy to install. Also on Honda's website they do have all the OEM accessories with the pdf's on how to install them. I have used the Honda documentation on how to install the auxiliary OEM Fog light, it's a 27 page pdf. Just follow that and it tells you exactly how to remove everything and even in what sequence.
|03-24-2019 01:12 PM|
|jalize||Thanks for the images, it help me quite a lot in installing my auxiliary spots on my 2019 ATAS.|
|03-24-2019 01:10 PM|
Originally Posted by Jonathan Parke View Post
I have wired my auxiliary spots from an Eastern Beaver 3 wire setup under the seat, ignition swithed 12V, through the OEM FOG Light switch and through to the dash via the Blue/Black wire on the front 4 way option plug.
|03-18-2019 11:22 AM|
Originally Posted by jege41 View Post
|03-18-2019 09:20 AM|
Originally Posted by playinatwork View Post
I want to wire up dash cam system would you recommend using the connections under the seat for this?
Any other suggestions as well would be appreciated for future electronic connections that I might add down the road.
|03-18-2019 05:39 AM|
Welcome to the forum.
I believe in this thread and others (just search for "front accessory" or "aux lights") you can find all info you need. The MY2018 has few electrical modifications comparing to previous versions, but the front and rear accessory sockets works the same.
You can choose to use the front accessory socket for both aux lights and GPS (like I did), but remember that total current absorbed from that connector should not be too high (5-6 amperes). If you have normal LED lights it should be ok. The connector is a Sumitomo HM090 (4 pins), if you want to do a "clean" work, best is use the corresponding connector (you can find it at Rugged Roads, I believe) and then cabling as you need.
If you plan higher wattage than probably it would be a good idea to use one of the power distribution kits available on the market (like the 3CS from Eastern Beaver). If you're not expert in electrics than better have some help from friends who understand the subject, just to avoid mistakes and streamline the work. The Eastern Beaver kits are ready to use and easier to install.
About the fairing it's not that difficult, but items must be removed in the correct order. You can find several videos on youtube that show you how to remove the plastics from a CRF1000L.
|03-17-2019 02:10 AM|
thank you for this thread and especially for sharing of your own experiences. It was a very inspiring reading for me ...
Well, I am actually playing with an idea to equip my ATAS 2018 with some 3rd party fog lights and a gps navi. But I have some concerns regarding to the disassembly and assembly of all those plastic things around the bike. Also to touch the electrics without any wiring diagram is very risky to me. Unfortunately, I am not such a brave guy like you are.
So I would very appreciate any support from you (diagrams, videos, pictures, hints and advices, etc.)
Does exist any Workshop manual for ATAS MY2018 (incl. wiring diagram)? If yes, where can I get it?
Many thanks in advance!
|This thread has more than 10 replies. Click here to review the whole thread.|